女人阴性道图片真人18

收藏本站 提供:電熱管價格和電熱管規格型號大全,還提供電熱管接線、選型的問題,特耐佳電加熱器高端電熱供應商。

模具加熱棒如何選購

今日出廠產品展示及部分報價

模具加熱棒如何選購

加熱器

模具加熱棒如何選購

在工業加熱設備使用鋼質加熱呈現出一頭出線的單頭加熱管,稱之為模具加熱管,在中國電熱行業,
In industrial heating equipment using the steel heating showing a lead single head heating tube, called a mold heating tube, electric industry in china,
稱謂的型號:M3;在國外稱為彈筒式加熱器。在選擇采購時要根據設備所使用的特征進行挑選,常規的模具單頭加熱管的有帶螺紋單端電熱管、L型單端電熱管、單頭加熱管等幾個樣式,常見的類型有內接高溫線式、外接高溫線式、出引出棒外接高溫線、直接出引出棒式這幾個類型。因此選擇時需要根據實際所使用的環境和設備進行選擇。
The title of model: M3; abroad as a cartridge heater. In the choice of procurement to selected according to the characteristics of the use of equipment, conventional Die single head heating tube with thread single end electric heating tube, L type single end electrothermal tube, single head heating tube and so on several styles, common types are inscribed high temperature wire type, external temperature line, a lead out rod outer the high temperature line, directly leads to the several types of stick. So choose according to the actual need by the use of the environment and equipment selection.
在模具單頭加熱管的設計過程當中需要了解是設計為單向接線還是雙向接線或者多種形式,材質的選擇也很重要是用有縫管還是無縫管或者不銹鋼管等,需要對加熱設備有個清楚的判斷。
In the design process of the injection mould for single head heating tube, need to know is designed for one-way or two-way connection or connection of various forms, the choice of materials is also very important is seamed tube or seamless pipe or stainless steel tube, need to have a clear judgement on heating equipment.
綜合分析模具加熱管不同的型號但是設計上的用材和性能都是有著共同點。模具單頭電熱管的性能要求如下:
Comprehensive analysis of mold heating tube of different models but timber and performance design are common. Die single head electric heat pipe performance requirements are as follows:
1、升溫時間。在試驗電壓下,元件從環境溫度升至試驗溫度時間應不大于15分鐘。
1, the heating up time. In the test voltage, components from the environment temperature to test time temperature should not exceed 15 minutes.
2、額定功率偏差。在充分發熱的條件下,元件的額定功率的偏差應不超過下列規定的范圍。
2, rated power deviation. In the full range of heating conditions, components of the power rating of deviation should be no more than the prescribed.
3、絕緣電阻。出廠檢驗時冷態絕緣電阻應不小于50兆歐姆。
3, insulation resistance. The factory inspection of cold insulation resistance should not be less than 50000000000000 ohm.
4、絕緣耐壓強度。元件應在規定的試驗條件和試驗電壓下保持1分鐘,而無閃絡和擊穿現象。
4, the insulation strength. Components should be in under the test conditions and test voltage for 1 minutes, but no flashover and breakdown phenomena.

相關文章

我要評論

*

*

051257123258
女人阴性道图片真人18